“Can I plant the potatoes first and put the irrigation in afterwards?” The answer is no, for a calendar reason. The plot must receive no water between planting and emergence, then it asks for a great deal as soon as stolons form, three to four weeks later. So the network has to be laid, pressurised and checked before the seed pieces go into the ground. Over a full cycle, FAO gives 500 to 700 mm for 120 to 150 days, and CNRADA puts the requirement at 5,000 m³ per hectare, the equivalent of 500 mm of water depth.
How much water the plot uses, and when
The cycle total is not enough to size a network, because the way demand is spread over time sets the peak flow rate. Alberta Agriculture and Forestry publishes the daily use of an irrigated potato crop, measured in the field: about 0.4 mm per day at emergence, up to 7 mm per day at full canopy and during tuber bulking, then a decline through maturity. The total seasonal requirement is given there as 400 to 550 mm in southern Alberta. A network sized on the cycle average therefore falls short exactly when the crop is building the harvest.
FAO expresses the same thing as a crop coefficient: 0.4 to 0.5 at the initial stage, 0.7 to 0.8 during development, 1.05 to 1.2 at mid-season and 0.85 to 0.95 in the late season. Multiplied by the reference evapotranspiration of your zone, that series gives the amount to replace stage by stage, and therefore the flow rate the equipment must hold at peak.
Second benchmark, the working depth. FAO states that 70 percent of the water is taken from the top 30 centimetres of soil and all of it from the top 40 to 60 centimetres. Alberta uses an extraction depth of 60 cm, with the same 70 percent share in the top 30 centimetres. So you are managing a small volume of soil: it empties fast and it refills fast. That is the central argument for light, closely spaced applications rather than large, widely spaced irrigations.
Third benchmark, tolerance to drying. FAO sets the rule at no more than 30 to 50 percent depletion of the total available water, and notes that beyond 50 percent yields fall. Alberta tightens it further for the sensitive phase: 30 percent allowable depletion at tuber initiation, 35 percent at the other stages, which amounts to keeping available water between 65 and 100 percent.
Sprinkler, furrow or drip: which one for potatoes
FAO states that the two most widespread methods on this crop are furrow irrigation and sprinkler irrigation, and that sprinkler irrigation replacing evapotranspiration every one to two days reaches very good results. It adds a point growers confirm on their own fields: frequent irrigation reduces tuber malformation.
- Sprinkler. It waters the whole ridge, suits the light and frequent applications the crop asks for, installs without a buried network and moves from one block to the next between campaigns. It is the default choice on an off-season potato plot, in free-draining soil as in medium-textured soil. The trade-off: it wets the foliage, which means running the sets early in the day so the canopy dries before nightfall.
- Furrow. It needs no energy if the plot has a regular slope and a water source at the head. It becomes hard to manage on a ridged crop that needs small doses: water runs along the bottom of the furrow, the top of the ridge stays dry, and uniformity falls apart as soon as land levelling is less than careful.
- Drip. It keeps the foliage dry, meters the dose to the litre and allows fertigation. It takes the lead where water is scarce, where it has to be lifted from a distance, or where available pressure is low. In exchange it demands serious filtration and one line per ridge, so a longer installation.
The choice rests on four figures measured before ordering: the flow available at the source in the driest month, the head to overcome, the soil texture and the slope. It is the same approach as in the field survey carried out before equipping a plot for irrigation, and it also decides the pumping set, as in sizing a solar pump for an onion plot.
Sizing sprinkler irrigation on a ridged plot
Three numbers are enough: the dose per application, the hourly application depth and the set time.
The dose per application is the one that brings the soil back to field capacity without going below the allowed depletion threshold. Alberta publishes these doses by soil texture, for the 60 cm depth, separating the tuber initiation phase from the other stages.
| Soil texture | Tuber initiation | Other stages |
|---|---|---|
| Loamy sand | 10 mm | 24 mm |
| Sandy loam | 13 mm | 29 mm |
| Loam | 16 mm | 38 mm |
| Silt loam and clay loam | 18 mm | 42 mm |
| Clay | 17 mm | 40 mm |
These doses are read together with peak demand: at 7 mm per day, a sandy loam plot given 13 mm at tuber initiation comes back for its next set about two days later. On loamy sand, with 10 mm, the interval tightens further. The frequency of the sets then dictates the number of blocks, and therefore the flow rate the station has to hold.
The hourly application depth, for its part, must stay below the infiltration rate of the soil, and the ridge complicates matters: it concentrates runoff into the furrow, where the water leaves without reaching the roots. Alberta recommends light, frequent and uniform applications, and cites reservoir tillage between the rows to hold water in place and even out soil moisture across the field. On a slope, this comes with laying out the sets along the contour lines.
Sprinkler spacing is then calculated from the wetted diameter and the prevailing wind, following the rules set out in our article on the distance between sprinklers. On potatoes, take the cautious end of those spacings: uniformity weighs more here than on a crop less sensitive to water deficit.
The irrigation calendar, from planting to harvest
CNRADA puts the best planting window in the first half of November for a February harvest, and as late as February in the oceanic zone and the oases for a May harvest. The cycle should not exceed 100 days from planting to the end of harvest; early varieties are lifted around 70 days, the others between 85 and 100 days. The reference spacing there is 30 cm by 60 cm, about 56,000 plants per hectare.
| Phase | Water management | Checkpoint |
|---|---|---|
| Planting to emergence | No irrigation | Alberta flags the seedpiece disease risk if you water before emergence |
| Emergence and vegetative growth | Light applications | CNRADA advises watering lightly early in the cycle to avoid tuber rot |
| Stolon formation and tuber initiation | Small doses, close intervals | Depletion capped at 30 percent according to Alberta; the most sensitive stage along with yield formation according to FAO |
| Bulking | Replace evapotranspiration, up to 7 mm per day | Available water held between 65 and 100 percent |
| Maturation | Progressive reduction | CNRADA advises reducing before haulm killing |
| Week before harvest | Full stop | Stop one week before lifting according to CNRADA |
Leaving the 65 to 100 percent band during bulking has a visible cost at harvest: Alberta cites hollow heart, knobby tubers and growth cracks. Conversely, lifting from soil that is too dry increases tuber damage.
One last detail that often slips past: water temperature. FAO warns against water cold enough to pull soil temperature below 15 to 18 °C. Where a deep borehole feeds the plot directly in the early morning, routing the water through a buffer reservoir solves the problem and doubles as regulating volume for the station.
The faults most often found on a potato irrigation network
- A single set for the whole plot, which forces long intervals and heavy doses, the opposite of what the crop asks for.
- An hourly application depth above the infiltration rate, recognisable from the water running down the furrow during irrigation.
- Sprinklers spaced too widely, leaving dry rings between nozzles and producing an uneven plot at lifting.
- Irrigation between planting and emergence, applied by reflex on dry soil.
- No measuring instrument. An auger tube and two or three tensiometers at 20 and 40 cm are enough to manage the depletion threshold instead of guessing it.
- An undersized filter at the head of the network on a surface water source, which ends up drifting the pressure and with it the uniformity.
Maintaining the network during the cycle
On a sprinkler system, useful checks come down to four actions. Read the pressure at the head and at the end of the lateral once a week: a widening gap signals a clogged filter or a leak. Check the rotation of every sprinkler at each set change, because a stuck head creates a dry patch within days. Measure nozzle wear at the end of the campaign, since a widened nozzle raises the flow and drops the uniformity. And flush the laterals before the first set of the following campaign.
On drip, the same reasoning applies to filtration and to flushing the line ends, according to the water quality measured before installation.
Preparing your campaign with JOGOO
JOGOO Agriculture sizes and installs sprinkler and drip networks, pumping stations and on-farm storage works. To have your potato plot studied, see our Irrigation and Pumping page, then write to us from the Contact page for a quote matched to your area and your water source. For the agronomic management of the crop itself, see our potato crop production guide.
Frequently asked questions
Should you irrigate right after planting?
No. Alberta Agriculture and Forestry recommends avoiding irrigation between planting and emergence to limit the seedpiece disease risk. Water resumes at emergence, in light applications.
How much water does a potato cycle need?
FAO gives 500 to 700 mm for a cycle of 120 to 150 days. CNRADA puts the requirement at 5,000 m³ per hectare, about 500 mm. The actual requirement depends on the reference evapotranspiration of your zone and on the length of the variety.
How often should the sets come round?
That follows from the dose per application and the daily requirement. On sandy loam, with 13 mm per application at tuber initiation and a peak of 7 mm per day, the set returns about every two days. On loamy sand it tightens, on clay soil it lengthens.
Does sprinkler irrigation encourage foliar disease?
It wets the canopy, so it lengthens the leaf wetness period. Run the sets early in the day so the foliage dries before nightfall, and watch the plot closely during cool, humid spells.
Can you fertilise through the irrigation network?
Yes on drip, where fertigation is standard practice. On sprinkler systems, solid application remains the rule and the network carries water only.
When should irrigation stop before harvest?
CNRADA recommends reducing applications shortly before haulm killing, then stopping completely one week before harvest.



